If your foundation has cracks wider than 1/4-inch wide, or if you have stairstep cracks in blocks or bricks, you can hire a contractor to plug them by injecting epoxy ($1,500-$3,000) or do it yourself with epoxy putty, but either way, you’ll only be stopping water from coming in.
You need to fix the underlying problem.
The most common culprit is water. It can accumulate in the soil around the foundation, which expands the soil and puts pressure on walls and foundation footings, causing cracks to appear.
Check to make sure all gutters and downspout drains are in good working order, and that the soil around your foundation is properly graded — it should slope at least 6 inches for every 10 horizontal feet.
Most foundations are required to have a perimeter drain system, such as a French drain, that channels sub-surface water away from the foundation.
It’s possible for this drain to become blocked, causing water to accumulate in the soil and putting pressure on your foundation walls. If you suspect a blocked drain, you will need to hire a professional to unclog it.
If Your Foundation Is Uneven
A foundation that has tipped, bowed, or severely cracked requires substantial reinforcement to prevent further deterioration.
Repair the walls from the inside with wood or steel braces, carbon-fiber mesh, or wall anchors spaced 6 feet or so apart along the entire wall.
For about $500 to $700 each, wood and steel braces install against the wall and attach to the floor and overhead joists, blocking further movement. However, they intrude into the basement area about 6 inches, making it difficult to finish the walls.
A newer option, which costs less than half as much and winds up almost invisible, involves spreading epoxy in vertical strips and then pressing on carbon-fiber mesh to lock the wall in place.
Wall anchors are similar to large bolts. They consist of metal plates in your yard (installed by excavating) and metal plates on the inside of your foundation walls. The plates are connected by steel rods buried horizontally. The connectors are gradually tightened to stabilize and help straighten the wall.
Wall anchors are placed every 6-8 feet, and cost $400-$600 each.
If a foundation wall bows severely (more than 3 inches) or if you want to make it straight again, you probably won’t be able to fix the problem from the inside.
You will probably need to excavate part or all of the foundation and rebuild it — a $30,000 to $40,000 job.
If Part of Your Foundation Is Washed Out
If a broken water pipe, a plugged gutter, or a drainage problem in your yard sent enough water cascading alongside a perimeter foundation to undermine an area, a contractor might be able to shore up the area with more concrete or shim the sill plate to make the area level again. Or you might need to tear out a section of the foundation, re-pour, and tie the new section into the old with rebar and epoxy.
Simple fixes with concrete and lumber might cost as little as $500 or as much as several thousand dollars. Just be sure that the underlying cause is fixed first, or the repair won’t last.
If You Find No Obvious Cause for the Problem
It may sit on soil that expands when damp and shrinks when dry. This so-called “expansive soil” is found in all states and has damaged about a quarter of all houses in the U.S., according to the American Society of Civil Engineers.
If you suspect that’s the problem, check with your local building authority to see if expansive soils exist in your area.
Dealing with this kind of soil is most difficult if you have a slab foundation because access underneath the slab is limited. First, try to reduce moisture fluctuations under your house. Make sure soil slopes away from the house, and pipe away all gutter water. Replace water-thirsty landscaping within 5 feet of the walls with plants that need little water or, even better, install a concrete path around the house so rainwater can’t soak in there.
If you live in a damp climate and notice settling issues such as sticky doors during droughts, try the opposite approach. Keep the soil evenly moist by running drip irrigation around the perimeter during dry spells. If you see cracks in the soil, it’s too dry. But don’t dump water into a crack; irrigate a foot or two away from the foundation, and use an automatic timer so you add a little water several times a day rather than a lot all at once.
A contractor may be able to raise a sunken area in the middle of a room by “mud-jacking,” or pumping a cement slurry under the slab under pressure.
Mud-jacking can’t raise load-bearing walls, however. For that, you need to support the slab with underpinning that reaches down to a more stable layer, a fix that costs $5,000 to tens of thousands of dollars.
Options for underpinning include steel posts driven in hydraulically, and helical piers, which have blades that screw into the soil. Installation costs $1,200-$1,500 per pier, with one every 6 to 8 feet.
Another option consists of pre-cast concrete pieces about 1 foot high that are pressed down on top of each other by the weight of the house, creating columns underneath.
Contractors tend to specialize in a single solution and often are quick to point out problems of other systems. That’s why it is so helpful to have a structural engineer’s guidance. In truth, the best option varies according to the circumstances.
Working With a Structural Engineer
Trustworthy advice comes from a structural engineer. An initial visit (about $500) should reveal the severity of your problem and tell you what to do next. If you need a full engineering report, expect to pay several thousand dollars. You might also need a soils engineer and core samples, doubling the cost.
In the end, you should get a written report that makes specific recommendations and lays out pros and cons of each option. If you need a complicated fix, you might want to hire the engineer by the hour ($100-$200) to inspect while work is underway.
Related: